Interesting Chips and Sensors


3D Hall Effect Sensors


 










The 3mm long TLE493D I2C interface 3D Hall Effect Sensor $1.97






 The Infineon TLE493D is a bit of a cost breakthrough at under $2. Using 3 Hall Effect sensors in a single package, this chip can identify the position of a near magnetic field, that can for example make a longer lifespan replacement for precision continuous rotation potentiometers, that I used to see in aerospace surplus.  There is an Arduino support library available for the I2C interface devices (be sure you know the version your working with), there are 4 different part numbers for the TLE493D-W2B6 fast wake-up chip, whose only difference is their I2C address, allows 4 of the 6 pin sensors to be used on a single bus.

 • 3D magnetic flux density sensing of ±160 mT   (1 miliTeslas = 10 gauss).
 • Programmable flux resolution down to 65 μT (typ.)   (Earth is 35-70  μT).
 • X-Y angular measurement mode.
 • 12-bit data resolution.
 • Sample rate: up to  8.4 KHz.

3D-MS2GO Evaluation Board, runs Arduino (Sensor at the Pointy End) $28.75

Magnetic Control Demos that snap on the eval board, the button can be rotated and pressed (Cost more than the board does)


Here's a worthwhile Tutorial-Review of the eval board for the older TLV493D-A1B6 from 2016:
Tutorial and Overview of Infineon’s 3D Magnetic 2Go Kit


The Infineon Mega "Getting Started Box IoT" eval. kit $145

For the serious R&D department, there is the Mega evaluation kit with 12 boards and adapters, and a couple of 3D sensor input controls.
  Includes: TLV493D 3D sensor, Current Sensor, MEMS Microphone, Biometric & Hardware Security chip. 3D sensor breakout shield (in place of the 3D-MS2GO above) , 2 tiny XMC 2Go boards that run Arduino,  an Arduino format host for the eval shields and an ESP32-Wemos.

Adafruit has a breakout board they sell using the older chip rev for $5.95 (not in stock at the moment)
  they provide a Circuit Python driver and reference the Infineon Arduino lib.


There are a number of Angular Position Sensors (like incorporated in some $50 controls that resemble a potentiometer), some of these chips use a 14 bit resolution sensor array, some examples:
  AS5170,  MLX90363 (3D sensor, digital output),  MLX90363 (analog output), KMT36H,  TLE5011 (circa 2011),  TLI5012B.

There are a number of angular sensor chips and modules available on the Chinese surplus market.

MLX90333 module handle joystick sensor absolute position digital three-dimensional angle
 board $4.37 AliExpress)
MLX90333 module handle joystick sensor


CJMCU-1335 Hall Effect 360 Non-Contact X-Y Plane(2D) Angle Sensor, 12 bit resolution $10.08 Aliexpress

CJMCU-1335 Hall Effect 360





BLE Enery Harvesting Switch

On Semi  BLE-SWITCH001-GEVB Eval kit $14.63




Useful for situations like a home automation setup where it's difficult to wire up a wall switch,  one could employ this gadget which uses the force of a switch press to generate sufficient energy (2× min. 0.33 mWs) to send out a bluetooth message.  BLE-SWITCH001-GEVB , sources: Digikey, Mouser ($13.75)





 Trimatic Advanced Stepper Motor Controller Family, MANY (94) offerings at Digikey
                       (Recently Demonstrated at a meeting)

Demo Video showing whine free 3D Printer

6 Most Economical Models:

Advanced Stepper Motor Control:TMC2208 SILENTSTEPSTICK  $7.32 Digikey

Ultra-silent motordriver IC for two-phase stepper motors.  up to 2A coil current (peak)

MicroPlyer™, SpreadCycle™, StealthChop2™


Benefits of using StealthChop2:
 -Significantly improved microstepping with low cost motors 
 -Motor runs smooth and quiet
 -Absolutely no standby noise
 -Reduced mechanical resonance yields improved torque


TMC SILENTSTEPSTICK TMC2100 (2.5A) board  $7.98 Digkey
  • MicroPlyer™, SpreadCycle™, StealthChop™
TMC2130 $12.73   (2.5A)   
microstep table,  MicroPlyer™, CoolStep™, passive braking,  short detection,  SpreadCycle™,  Stall detection,  StallGuard2™,  StealthChop™

TMC2209 $14.70  (2A)
MicroPlyer™, CoolStep™, short&Stall detection,  SpreadCycle™, StealthChop2™, StallGuard4™

TMC5160 $15.00   High Power with External Transistors
MicroPlyer™, CoolStep™, passive braking, short detection, SpreadCycle™, Stall detection, StallGuard2™, StealthChop2™


BREAKOUTBOARD WITH TMC5160 $21.40  includes ext MOSFETS (AO4882 Dual-N)
( 2.8A continuous / 3.1A peak) 
TMC5160 Breakout Board





Comments

Post a Comment

Popular posts from this blog

Hooking up the 6 + 1 Mic Array to the MaiX BiT

Image
The Risk-V chip on the MaiX BiT board also contains hardware FFT which should make it a respectable audio analysis board.  Sipeed offers a microphone array board with 7 mics and 12 RGB LEDs. Unfortunately the mic array, which SeeedStudio  indicates is for Dock/Go/Bit, there is no real provisions made for the newer BiT board. Included with the mics is a 10 pin ribbon cable for the Go board, and an unadvertised (not on sales page inventory) 5x2 "dupont" connector cable which directly connects between the back of the mic array (not pictured on the sales page) and the Dock board area with mic connection labels silk screened on the board. Some improvising is needed to hook up the BiT.  I offer 2 different solutions. The first that Seeed could help by throwing in a couple of replacement connector housings. Connection Method #1 (You might have to start with a larger housing and cut it down to size) The Seed OPL type for ...
Read more

Holographic Fans Getting Real Time HDMI Input

Image
 One of the technical leaders in so called 3D Holoographic LED Fans is Dseelab, in Sep 2019 they announced at an event the development of real time HDMI Video Input, it may be quite a while befiue it reaches the market.  Achieving this has been my holy grail, looking into FPGA based video processors and examining cartesian to polar code may no longer be necessary... Here's an interesting demo recently posted: Dseelab a leader in the "3D Holographic LED Fan" industry, has master-slave connections on their units, allowing them to be syncronized in an array, they also offer a programming API connecting though WiFi or with a wired serial connection to a PC.  The API supports remote update from the cloud and random play of 256 different media assets. The only other Holographic Fan maker offering a programming API and arrays for large image display is HYPERVSN of  Ireland.  The newest addition to the DseeLab line is their: 6 Blade 78cm, 960*960 res, ...
Read more

LED Driver Roundup

Image
LEDs being current, rather than voltage operated devices require special driver circuits for optimal performance.  While simple applications like an indicator light that might be run at a fraction of it's rated capability, a series current limiting resistor is sufficient.  High power application running at the edge of the LED's max current rating require active regulation to compensate for the negative temperature coefficients of the LED, (measurement techniques are discussed in this university lab paper .) Low power LEDs can be driven with simple series resistor current control when powered from a regulated power supply. The LED Load Line graph be low helps one select a standard resistor value to get the ballpark current setting with a 5 volt power source.  Find where your LED's color line intersects the desired current, then pick the closest resistance line below that intersection. (This graph is from LEDnique.com , a collection of basic articles on LEDs aime...
Read more